Audio / Video Cables & Adapters › IEC › Coaxial › BNC

IEC BNC-RG11 BNC Male Coax Connector for RG11

Manufacturer part number: BNC-RG11 Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59 and... more

IEC BNC-RG58-TW BNC Male Coax Connector Twist-on for RG58

Manufacturer part number: BNC-RG58-TW Doesn t require any tools. Good for fast short term cable terminations for good terminations use . Full description: Weight0.032 lbsWire Type Plenum RG58 RG58 RG59 and RG62 RG59 and RG62 Plenum more

IEC BNC-RG174 BNC Male Coax Connector for RG174 50 Ohm

Manufacturer part number: BNC-RG174 Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59... more

IEC BNCF-F BNC Female to Female Splice Coax Connector

Manufacturer part number: BNCF-F Use to join two coax cables for extended length. Signal loss may be equivalent to about 10 feet of cable (so joining two 30 foot cables with this will be 60 feet but will have the same loss as a 70 foot one piece... more

IEC BNC-RG179 BNC Male Coax Connector for RG179 75 Ohm

Description Occasions: Daily Life Party Christmas Gift Item type: Bracelet Material: Alloy Quantity: 12pcs/set Size : adjustable Condition: 100% Brand New Conversion : 1 cm = 0.39inch or 1mm = 0.0393 inch Note: Due to the light and screen setting... more

IEC BNC-RG58-PL BNC Male Coax Connector for Plenum RG58

Manufacturer part number: BNC-RG58-PL Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59... more

IEC BNC-735A BNC Male Coax Connector for DS3 735A 75 Ohm

Manufacturer part number: BNC-735A Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59 and... more

IEC ADP7053 Balun - BNC Male to RJ45 93 OHM

Manufacturer part number: ADP7053 Baluns allow you to run an ARCnet™ or IBM™ 3270 coax type signal through twisted pair wire. Two would actually be needed to make a connection one at each end of the twisted pair wire.On the RJ11 () the active pins... more

IEC BNCT-1M BNC T Male to Female to Female Coax Connector

Manufacturer part number: BNCT-1M Used to join three BNC cables. If used with a bus network the cable from this to the network card (the drop ) can t be too much longer than 3 feet. Full description: Weight0.02 lbsStyle T Female - Female - Female T... more

IEC BNCPS-RG59 BNC Male Coax PermaSeal Connector for RG59

Manufacturer part number: BNCPS-RG59 Full description: Weight0.04 lbsWire Type RG59 RG6 RG6 Quad Shield RG6 White more

IEC BNC-RG62-TW BNC Male Twist-on Coax Connector for RG59 and RG62

Manufacturer part number: BNC-RG62-TW Doesn t require any tools. Good for fast short term cable terminations for good terminations use . Full description: Weight0.032 lbsWire Type Plenum RG58 RG58 RG59 and RG62 RG59 and RG62 Plenum more

IEC BNC-RG59-75 BNC Male 75 Ohm Coax Connector for RG59

Manufacturer part number: BNC-RG59-75 Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59... more

IEC BNCF-RG62-PL BNC Female Coax Connector for RG59 and RG62 Plenum

Manufacturer part number: BNCF-RG62-PL Full description: Weight0.02 lbsWire Type RG58 RG59 and RG62 RG59 and RG62 Plenum RG174 50 Ohm RG179 75 Ohm RG58 Reverse Polarity (Male Pin) more

IEC BNC-RG6-75 BNC Male 75 Ohm Coax Connector for RG6

Manufacturer part number: BNC-RG6-75 Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59... more

IEC BNCF-NF BNC Female to N Female Coax Adapter

Manufacturer part number: BNCF-NF Adapter adapts a BNC on the end of a cable to a different connector on the panel will not change impedance. Cable must have impedance required by equipment. Full description: Weight0.02 lbsConnector F100 Male N-Type... more

IEC BNCPS-RG6 BNC Male Coax PermaSeal Connector for RG6

Manufacturer part number: BNCPS-RG6 Full description: Weight0.04 lbsWire Type RG59 RG6 RG6 Quad Shield RG6 White more

IEC BNCF-RG58 BNC Female Coax Connector for RG58

Manufacturer part number: BNCF-RG58 Full description: Weight0.02 lbsWire Type RG58 RG59 and RG62 RG59 and RG62 Plenum RG174 50 Ohm RG179 75 Ohm RG58 Reverse Polarity (Male Pin) more

IEC BNCM-NF BNC Male to N Female Coax Adapter

Manufacturer part number: BNCM-NF Adapter adapts a BNC on a panel to a different connector on the end of a cable will not change impedance. Cable must have impedance required by equipment. Full description: Weight0.03 lbsConnector N-Type Female N-Type... more

IEC BNCF-F-75 BNC Female to Female 75 Ohm Splice Coax Connector

Manufacturer part number: BNCF-F-75 Use to join two coax cables for extended length. Signal loss may be equivalent to about 10 feet of cable (so joining two 30 foot cables with this will be 60 feet but will have the same loss as a 70 foot one piece... more

IEC M5284 Video 4 BNC Coaxial Cable (Composite Sync) 6

Manufacturer part number: M5284 Full description: WeightN/ALength 6 Foot 6 Foot Molded more

IEC BNCT BNC T Female to Female to Female Coax Connector

Manufacturer part number: BNCT Used to join three BNC cables. If used with a bus network the cable from this to the network card (the drop ) can t be too much longer than 3 feet. Full description: Weight0.02 lbsStyle T Female - Female - Female T Male -... more

IEC BNC-RG59 BNC Male Coax Connector for RG59

Manufacturer part number: BNC-RG59 Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59 and... more

IEC BNCF-F-MT-75 BNC Female to Female Bulkhead Coax Connector Rated for 75 ohm impedance

BNC Female to Female Bulkhead Coax Connector Rated for 75 ohm impedance more

IEC BNCF-MT BNC Female Bulkhead Coax Connector

Manufacturer part number: BNCF-MT If you use the solder type connector our soldering iron is . to see our list of crimping tools for BNC connectors. Mounts in a 3/8 (.375) inch hole Full description: Weight0.01 lbsWire Type Plenum RG58 RG59 and RG62... more

IEC BNCF-RG62-PL-MT BNC Female Bulkhead Coax Connector for RG59 and RG62 Plenum

Requires the IDL30-591 crimp tool or the IDL30-591 die that fits into the IDL30-506 crimp tool handle. Mounts to a wallplate with a BNC cutout. The WZ10102 and WZ10104 are just two of the many wall plates this can be used on just look for the 01 as the... more

IEC BNC-RG62-PL BNC Male Coax Connector for RG59 and RG62 Plenum

Manufacturer part number: BNC-RG62-PL Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59... more

IEC BNCY-1M BNC Y Male to Female to Female Coax Connector

Manufacturer part number: BNCY-1M Used to join three BNC cables. If used with a bus network the cable from this to the network card (the drop ) can t be too much longer than 3 feet. Full description: Weight0.02 lbsStyle T Female - Female - Female T... more

IEC BNCF-F-MT BNC Female to Female Bulkhead Coax Connector

Manufacturer part number: BNCF-F-MT Use to join a coax cable inside a wall to a coax patch cable outside the wall. Mounts to a wallplate with a BNC cutout. The and are just two of the many wall plates this can be used on just look for the 01 as the... more

IEC BNC-RG58-ST BNC Male Coax Connector for Stranded RG58

Manufacturer part number: BNC-RG58-ST Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59... more

IEC BNC-8218 BNC Male Coax Connector for Mini 75 Ohm (Belden 8218)

Manufacturer part number: BNC-8218 Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59 and... more

IEC BNCM-M BNC Male to Male Splice Coax Connector

Manufacturer part number: BNCM-M Adapter adapts a BNC on a panel to a different connector on the end of a cable will not change impedance. Cable must have impedance required by equipment. Full description: Weight0.03 lbsConnector N-Type Female N-Type... more

IEC BNCM BNC Male Coax Connector for RG58 RG59 and RG6 works on both PVC & Plenum

Manufacturer part number: BNCM Some variations may need to have the center pin soldered onto the wire our soldering iron is . to see our list of crimping tools for BNC connectors. Full description: Weight0.026 lbsWire Type Plenum RG58 RG58 RG59 and... more

IEC BNCF-RG62-MT BNC Female Coax Connector Bulkhead for RG59 and RG62

Requires the IDL30-502 crimp tool or the IDL30-581 die that fits into the IDL30-506 crimp tool handle. Mounts to a wallplate with a BNC cutout. The WZ10102 and WZ10104 are just two of the many wall plates this can be used on just look for the 01 as the... more

IEC M5285 Video 5 BNC Coaxial Cable 6

Manufacturer part number: M5285 Full description: WeightN/ALength 6 Foot 6 Foot Molded 10 Foot 10 Foot Molded 15 Foot 25 Foot 25 Foot Molded 35 Foot 50 Foot 75 Foot 100 Foot more

IEC BNCF-NM BNC Female to N Male Coax Adapter

Manufacturer part number: BNCF-NM Adapter adapts a BNC on the end of a cable to a different connector on the panel will not change impedance. Cable must have impedance required by equipment. Full description: Weight0.02 lbsConnector F100 Male N-Type... more

IEC BNC-RG58-PL-TW BNC Male Coax Connector Twist-on for Plenum RG58

Manufacturer part number: BNC-RG58-PL-TW Doesn t require any tools. Good for fast short term cable terminations for good terminations use . Full description: Weight0.032 lbsWire Type Plenum RG58 RG58 RG59 and RG62 RG59 and RG62 Plenum more

IEC BNC-RG62-PL-TW BNC Male Twist-on Coax Connector for RG59 and RG62 Plenum

Manufacturer part number: BNC-RG62-PL-TW Doesn t require any tools. Good for fast short term cable terminations for good terminations use . Full description: Weight0.032 lbsWire Type Plenum RG58 RG58 RG59 and RG62 RG59 and RG62 Plenum more

IEC BNCF-RG58-PL-MT BNC Female Bulkhead Coax Connector for RG58 Plenum

Requires the IDL30-591 crimp tool or the IDL30-591 die that fits into the IDL30-506 crimp tool handle. Mounts to a wallplate with a BNC cutout. The WZ10102 and WZ10104 are just two of the many wall plates this can be used on just look for the 01 as the... more